Posts

Posted on

Oil’s Well That Ends Well (Oil Change Grades and Weight)

Changing your oil regularly is one of the most important things you can do to keep your vehicle running well.  And knowing the right type of oil to use is also very important. 

Engine oil is classified by weight, but it doesn’t refer to how much the oil would weigh if you put it on a scale.  It refers to viscosity, or how easily the oil flows through the engine.  Most engines operate normally at around 210°F/99°C.  The viscosity, or weight, is assigned a number by how well it flows at that temperature.  The lower the number, the more freely it flows. 

Most vehicle engines use what’s called a multigrade oil which behaves differently in different temperatures. Multigrade oils have a “W” in their viscosity number that you may have seen on a bottle of oil, something like 5W30.  The W stands for winter and shows how freely it flows in colder temperatures.

That means a 5W30 oil will behave like a 5 weight oil in lower temperatures (less viscous or thinner) and a 30 weight oil in warmer temperatures (more viscous or thicker).  That’s important on a cold day because the oil needs to behave like a thinner oil when you start your engine since it need to lubricate engine components immediately to protect the metal components. Then as the engine warms up, it behaves like a thicker oil to prevent friction among those parts.  Pretty neat trick, right?

The type of oil you use can differ depending on what type of climate you operate your vehicle in and how your vehicle is used (carrying big loads, towing, etc.). Your owner’s manual contains several different recommendations based on these factors.  Your service advisor can recommend the right oil for your needs.  Like Shakespeare said, “Oil’s well that ends well.”

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

Alleviate the Creaks and Squeaks (Chassis Lubrication)

If your vehicle creaks and squeaks when you drive down the road, it may mean that some of the metal parts are rubbing against each other and need to be lubricated.  Those could be parts of the suspension, steering system and the drivetrain. 

Years ago, most vehicles had to have their chassis (what you think of as the frame) regularly lubricated.  Newer vehicles are made with what some call “lifetime lubrication,” but there are still parts of the chassis that need to be maintained with lubricants.  Your service advisor can help you know when that needs to be done.

In your owner’s manual, the vehicle’s manufacturer lists components that need regular maintenance. Things like u-joints, steering joints, sway bars, bushings and joints in the suspension. Some of them may have that “lifetime lubrication,” while others may not. When you bring your vehicle in for service, a technician will look for any parts that have grease fittings.  They will inspect these components, clean the fittings so dirt and other contaminants won’t be forced into the part and then lubricate them with a lubricant that meets the manufacturer’s specifications. 

Sometimes a chassis lubrication is done at the same time as an oil change.  That’s also an ideal time for the technician to check other parts of your vehicle that may need attention.  That could include greasing other parts such as the fuel door, trunk and door hinges, suspension springs and door latches.

Times have changed since the days when a “lube” job was synonymous with an oil change. Depend on your owner’s manual and advice from your service advisor to know when “grease” is the word—and appropriate for your vehicle.

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

Put the Brakes On! (Brake Caliper Replacement)

Keeping your vehicle’s brakes in top shape is one of the most important things you can do for your safety and those on the road with you. Most drivers know a little about brake pads and rotors but maybe not so much about another brake component called the calipers.

Disc brakes work by a mechanical system that presses your brake pads against discs called rotors (you can usually see these discs through your wheels). The friction stops your vehicle smoothly when everything is working the way it should.  The calipers use the hydraulic pressure of the brake fluid to apply the stopping power. 

After they’ve been on your vehicle for a while, the calipers can get stuck or wear out.  If calipers on one side of the vehicle work correctly and not on the other, you might feel a pull in one direction.  You might feel the same kind of pull if the caliper is stuck and is applying constant pressure.  You might hear scraping or squealing coming from a stuck caliper and you might smell burning on that side.  The friction from a caliper that’s always applying pressure may cause that wheel to heat up, so after you’ve pulled your vehicle off the road safely, the wheel with the stuck caliper will might feel hotter than the others

Because there are many different components to the brakes, it’s best to leave the diagnosis and repair to a trained technician. They will run each wheel through a series of tests and inspections that can pinpoint the problem.  Sometimes it involves more components than just the caliper that may need changing at the same time.

The best way to make sure your brakes will perform well is to is to have our service center perform regular inspections and follow the vehicle manufacturer’s recommended service.  That way your brakes will be ready, willing and able when you call on them to put a stop to things.

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

All Lined Up (Alignment Inspection)

When you head down a straight road, does your vehicle pull to one side?  Do you feel vibration in any of the wheels? If you’ve noticed any of these things, it’s probably time for you to get your wheel alignment checked.

When your vehicle left the factory, its wheels were parallel to each other and perpendicular to the ground.  That maximizes traction for good steering and braking. Every time you take your vehicle on the road, normal wear and tear will affect your alignment. Hit a bump, a pothole or a curb and all those little knocks will add up

Bad alignment not only can cause your steering wheel to pull unevenly, it can also wear your tires out a lot faster than they should. In fact, if you look at your tires and see one side of the tread is a lot smoother than the other, it could be another sign of bad alignment.

Since different problems can cause similar symptoms, the first thing our trained technician will do is test drive your vehicle. Then, they’ll check the front end and steering linkage as well as look for tire wear.  Then, the technician will put your vehicle on a lift and use computerized diagnostic equipment to measure alignment angles so they can precisely align your vehicle’s components.

There are different kinds of alignments.  One is a front-end alignment that aligns components of the vehicle’s front axle.  Another is a thrust alignment that makes sure the front wheels are lined up with the direction the rear wheels are pointed.  A third type is four-wheel alignment which is usually used on all-wheel drive and  4-wheel drive vehicles.  It’s also recommended for front-wheel drive vehicles that have independent rear suspensions.  It makes sure the angles of all the wheels are where they should be relative to each other and also the vehicle’s body or frame.

Your steering wheel should be perfectly centered if you are heading straight down the road, so the technician will adjust it so it is. Finally, they’ll take your vehicle back on the road for a final test drive to make sure it’s performing the way engineers intended.

Your service adviser can recommend how often you should have your alignment inspection, since it depends on the type of vehicle you drive (SUV, sporty car, etc.) and your driving environment.  Properly aligned wheels can help your vehicle perform better and save you from expensive repairs down the road.

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

More than Pads and Rotors (Brake Caliper Replacement)

You might be familiar with brake pads and rotors, two components of your vehicle’s brakes that have to be regularly serviced.  Here’s another important component of your brakes: the calipers.

Calipers are used in disc brakes, the type of brakes now found in most recently manufactured vehicles.  A caliper is the part of the brakes that squeezes the brake pads against the discs, or rotors, which turn with your wheels. 

There are different kinds of calipers, but the basic principle is the same.  You press down the pedal, brake fluid activates a piston or pistons that squeeze the brake pads against the disc and the friction slows down your vehicle.

While modern vehicles have a warning system to let you know it’s time to get your brakes checked, your brake light usually goes on when your fluid level is low or your fluid pressure is low.  But you may have to look out for signals your calipers are the problem. 

If your vehicle pulls to one side when you brake, that could be a sign that one caliper isn’t working right.  If you smell a burning odor coming from a wheel after a trip, there might be too much pressure from a caliper.  Grinding or squealing when you brake is another signal that it may be time to bring in your vehicle so we can check your brakes.

One way to minimize brake issues is regular inspection.  Have them periodically looked at when you bring in your vehicle for an oil change.  The good news is brake issues are more likely to be caused by pads or rotors wearing out.  Calipers last a lot longer, but even they will need replacing every so often.  

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

To Fix or Not To Fix (Tire Repair)

You know that sinking feeling when you realize one of your tires has a problem.  It may be making an odd noise or behaving oddly when you’re driving.  You may hit a pothole or curb and one suddenly goes flat.  Or you may head back to your vehicle and discover it has one tire deflated without a clue of what must have happened to it.

With a lot of different tires hitting the streets these days, the issue of whether to have a tire repaired or replaced can be tricky, and we strongly recommend you have a trained technician help you make that decision. 

One of the most common causes of flat tires is picking up a screw or nail in the tread area.  Many of those can be patched and plugged if the puncture isn’t more than ¼ inch/6 mm in diameter. Most tires can handle two of this type of repair, but any more and you should buy a new tire. 

If there’s a puncture or bulge in the sidewall or shoulder, the rule of thumb is it’s not repairable.  The sidewall doesn’t have the reinforcements that the tread area does.  In fact, any puncture that’s more than a ½ inch/12 mm away from the edge of the tread should not be fixed. 

Many newer vehicles have no spare tires (to save weight and fuel) and instead have a type of tire called “run-flat.”  Sometimes, the only way you know they’re deflated is when the tire pressure monitor alerts the driver.  Driving on them more than 50 miles/80km can render them un-repairable.  They may be fixable if you pulled off to the side of the road before driving on them too long. Our technicians can evaluate whether they can be driven further or should be replaced.

Other vehicles with no spare include a can of tire sealant and a compressor.  If you use it, tire experts say to have the tire professionally repaired as soon as possible.

If you have had a flat tire, try not to drive on it unless it’s necessary to get your vehicle away from a dangerous situation.  Our technicians can evaluate any tire you may be having problems with and recommend whether repair or replacement is the best option. Your safety is riding on your tires.  

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

Heat and your Tires (Tire Pressure Monitoring System)

With hotter weather and brutal heat waves becoming more common, the pressure in your vehicle’s tires goes up.  After all, heat causes air to expand, and the air in your tires follows the laws of physics. Overinflated tires can reduce your vehicle’s traction, cause a hard, punishing ride and make your tires wear out faster; all are important safety issues.

Four out of every ten drivers rarely check tire pressure. Some rely on their vehicle’s tire pressure monitoring system (TPMS) to keep an eye on proper tire inflation.  But it’s not designed to do that.

TPMS is a safety feature that has been required on vehicles made in 2008 or later, using sensors in the wheels that alert you to tire pressure problems.  That warning can be a light on your dash, a digital message or a readout of the pressure in each individual wheel.  But a study showed that more than 40 percent of drivers don’t even know what the tire pressure monitoring light symbol looks like!

One looks like a horseshoe with an exclamation point in the middle.  The other looks like an overhead view of your vehicle with the tires at all four corners.  They may even show the inflation number (usually in pounds per square inch, or PSI).

The TPMS is designed to alert you that your tires aren’t inflated within certain parameters, but the system shouldn’t be a substitute for frequently having your tires checked with a tire gauge.  A TPMS light is only required to come on when a tire is 25 percent under the recommended tire pressure; by that time, you’re driving on an unsafe tire and causing excessive wear.

Have your vehicle checked regularly by our professionals, and that includes tire pressure checks.  If you do see the tire pressure warning come on, have our service center look at it soon.  You may have a tire with a problem or the TPMS system may not be working right. 

Either way, since your tires are the only contact your vehicle has with the road, your safety depends a great deal on your tires being in top shape and correctly inflated.  Keep your tires properly inflated and your TPMS working to alert you of any problems. And that’s not just a lot of hot air.   

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

Road Trip? Check! (Trip Inspection)

After months of postponing travel far away from home, a lot of us can’t wait to hit the road and scream “Road Trip!” again.  But how long has it been since the vehicle you’re planning on taking has had a thorough inspection? And is it roadworthy for several days on the highway? Time to schedule a professional trip inspection in our service center. 

When it comes to long trips, before you go, make sure you can stop.  We can perform a break inspection.  Our technician will visually inspect your brakes for wear and how much life is left in the brake pads and rotors.  They’ll also check your brake lines and fluids for fitness and fill.

If it’s going to be a long trip, it’s important that your engine stays lubricated.  The technician will see when the last time you had an oil change, check the levels and inspect the system for leaks.  If you are close to needing an oil change, it’s best to have it done before the trip because no one wants to interrupt a vacation with an oil change in a strange place.  It’s also better for your engine to have fresh, clean oil rather than driving with dirty, worn-out oil.

Comfort in any vehicle depends partly on the suspension system.  Our technician can examine shocks and struts so you can avoid an uncomfortable and potentially unsafe journey.  Oh, and you’ll definitely want to make sure your wheels are aligned.  A long trip in an out-of-alignment vehicle can be a driving nightmare with potential steering problems and tire damage. 

A couple of little things some drivers take for granted are the engine air filter and wiper blades.  A dirty air filter can cost you money by reducing fuel economy; it adds up on a long trip.  And worn-out wiper blades can make visibility while driving in a rainstorm a blinding, unsafe adventure that you never want to experience, especially in unfamiliar territory.

If you’re in the habit of having your vehicle regularly maintained, many of these items may be in excellent condition.  But considering the extra stresses a long road trip places on any vehicle, it’s nice to have a set of our trained eyes give your vehicle a closer look. That way you’ll be able to gaze YOUR eyes on sights like the Leaning Tower of Niles or the Gopher Hole Museum. 

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

Round and Round (Wheel Balancing)

In a perfect world, all wheels and tires would be perfectly round and weigh exactly the same at every point of the wheel.  Unfortunately, they’re not, and if they’re out of balance, they can reduce the lifespan of your tires, make your vehicle shake like a carnival ride, and maybe even damage a few suspension parts along the way.  You don’t want that!

Wheel balancing, sometimes known as tire balancing, is a process by which a technician makes sure your tire/wheel assembly has evenly distributed weight.  If it isn’t, it can give your ride bad vibrations.  If you feel your vehicle’s steering wheel shaking, it can mean unbalanced wheels in the front. If you can feel a vibration in your seats, it could be unbalanced rear wheels.

In addition to your vehicle vibrating at higher speeds, there are other signs that your wheels are out of balance. You may see uneven tread wear, or you may notice you aren’t getting the kind of fuel economy you used to. 

When you experience these problems, bring your vehicle in, and we can put your wheels on a machine designed to detect any imbalance.  The technician will start your wheels spinning, and a computer will determine how much weight is needed where.  Then, the technician can add small weights on the inside or outside of your wheel rim to precisely balance out the uneven weight.  When the wheel is balanced correctly, it will spin evenly and smoothly.

Sometimes your vehicle will hit a pothole or object in the road that dislodges one of those weights, which can throw that wheel out of balance again.  If so, you’ll have to bring it in to have that corrected

Some drivers confuse wheel balancing with wheel alignment. Alignment is making sure the wheels are perpendicular to the road and parallel with each other.  Sometimes your vehicle will need both balancing and alignment done at the same time.

No vibrations are good vibrations when it comes to your wheels.  Bring your vehicle to us, and we’ll perform a balancing act to keep your vehicle riding smoothly down the road.

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com

Posted on

Rotation Explanation (Tire Rotation Patterns)

You may notice that when you get your vehicle’s oil changed, your service adviser may recommend that you have your tires rotated at the same time.  The reasons are simple.  That will allow your tires to wear more evenly and reduce the noise your tires make as you drive down the road.

There are different ways of rotating tires. If your vehicle has non-directional tires and the same size wheels at each corner, here are the different rotation patterns.

For all-wheel drive and rear-wheel drive vehicles, one is called the rearward cross pattern.  The rear tires are moved to the front and stay on the same side of the vehicle, and the front tires are moved to the rear on the side opposite of where they were on the front. 

For all-wheel and four-wheel drive vehicles, use the X pattern.  The rear tires are moved to the front on the opposite side of the vehicle, and the fronts are moved to the rear on the opposite side of where they were on the front.

For front-wheel drive, there’s the forward cross.  The front tires are moved to the rear wheels on the same side of the vehicle as they were on the front and the rear tires are moved to the opposite side of the vehicle than they were on the rear. 

If you have directional tires (they only can be mounted in one direction) and the same size directional wheels, the rear tires are moved to the front on the same side of the vehicle where they were, and the front tires are moved to the rear on the same side they were on the front.   And if you have tires with different sizes of non-directional tires and wheels on the front and rear, rotation will be from one side of the vehicle to the other. 

If you have a spare, it’s put into the rotation using a forward cross or rearward cross. 

Yep, that’s a lot to keep straight.  So, we suggest letting your service advisor recommend the right rotation pattern for you at the interval your vehicle’s manufacturer specifies.

Tylers Auto TV
12485 SW MAIN ST
TIGARD, OR 97223
(503) 639-5588
http://www.tylersautomotive.com